1. Spa Controls
2. Spa Pumps
3. Spa Packs
4. Top Sides & Wifi
5. Circulating Pump
6. Pool Pumps
7. Spa Blowers
8. UV Sanitizer
9. Ozonator
10. Chlorine/Ozone
11. Spa Heaters
12. Balboa Heaters
13. Any Size Pumps
14. Airbleeder
15. Pump Motors
16. Wet Ends & Volutes
17. Blower Motors
18. Boards & Sensors
19. Electrical Components
20. Plumbing Components
21. Air Buttons
22. Management
23. Baptismal Products
24. Spa Lights
25. Universal Spa Motors
26. Spa Massagers
27. Portable Hot Tubs
28. Filters & Testers
29. General Part List
30. Product Information
31. Manuals & Guides
32. Wiring Diagrams
33. Troubleshooting
34. Terms & Conditions
35. Limited Warranty
36. Returns, Repairs & Warranty Claim Form
37. Proper Water Chemistry
38. Watkins Heaters
39. Watkins Pumps
40. Watkins Controls
41. Sundance Controls
42. Gecko Controls
43. Balboa Controls
44. ACC Boards
45. Resale Info
PM5010 Top Side Control
PM5010 Digital Top Side Control
PM5010 with PM5010D Decal
Current decal color design may not match picture

[Fig. A]
Dimensions British (Metric):
Width = 4.55" (11.56cm) | Length = 9.75" (24.77cm)
Hole Saw Size:
Width = 3.50" (8.89cm) | Length = 8.10" (20.57cm)
NOTE: Throughout the years we have sold these spa side controls to many spa distributors and spa manufacturers without a decal. They would supply their own decal on our Smart Touch controller. The spa side control is the same, however the decal may be different.
When you purchase this spa side control direct from us we can only provide a decal when purchased from Table (1) below.
Your original decal may not have the same color or the same number of buttons. Our decal exposes all the buttons of the spa side control whether your original decal supported them or not. All Top Side controllers functions are the same regardless of the decal.
It is just a decal and has no effect on the spa operation.
PM5010 Digital Top Side Control
PM5010 without PM5010D Decal

[Fig. B]
Prices include Free Freight*
IMPORTANT! Total cable length between Controller and Top Side MUST NOT exceed 100 feet!


    How To Replace Your Digital Spa Side Control Panel
  1. Turn the power OFF.
  2. Remove the spa access panels of your spa cabinet.
  3. Locate the digital spa controller.
  4. Unclip and remove the grey ribbon cable connecting the digital spa side control where it connects to the spa controller.
  5. The top side control is usually secured to the spa shell by either a dual-sided adhesive gasket or by silicone.
  6. Using a putty knife, carefully pry the old spa side control and adhesive or silicone away from the spa shell.
  7. Remove the old spa side control and the grey ribbon cable attached to it.
  8. Clean the opening on the spa shell to remove all the old silicone or any remnants of the gasket.
  9. Using the same adhesive method as your old spa side control, mount the new spa side control on the spa shell.
  10. Connect the grey ribbon cable attached to the new spa side control to the spa controller where the old cable was connected.
  11. Turn the power ON. Test all functions.


*Free Freight only for Fedex SmartPost. Other forms of shipping incur additional shipping costs.

**Beating competitor's price: We will meet or beat any competitor's written quotation for hardware of the same capability, such as: plumbing size, voltage, motor horsepower, motor 1 or 2-speed, heater length, safety test report, etc.

A $9.95 Handling charge is applied to all orders.

All products sold per our "Terms and Conditions" found in the "Support" section of our menu.

When your order is produced, the pump motor used (A.O. Smith, Regal Beloit, Marathon Electric, etc.) will be whatever is in stock in our factory at the time.